Search results for "Air gap"
showing 10 items of 14 documents
Assessing the influence of fieldshaper material on magnetic pulse welded interface of Al/Cu joints
2019
Abstract Fieldshaper (FS) is a widely used component in magnetic pulse forming and welding to improve the efficiency of the process. It enables to increase the magnetic pressure experienced by the workpieces during forming and welding. Recent developments in this subject focuses to increase the life time of the fieldshaper and to improve the efficiency by introducing shape optimized designs. In this study, we compare the efficiency of four fieldshapers made of Cuprofor, Siclanic, CuBe2 and Steel. The main focus is given to the effect of material properties while the same geometry was considered for those four fieldshapers. The same welding conditions (discharge voltage of 6kV and air gap of…
Parallel distributed compensation for voltage controlled active magnetic bearing system using integral fuzzy model
2018
Parallel Distributed Compensation (PDC) for current-controlled Active Magnetic Bearing System (AMBS) has been quite effective in recent years. However, this method does not take into account the dynamics associated with the electromagnet. This limits the method to smaller scale applications where the electromagnet dynamics can be neglected. Voltage-controlled AMBS is used to overcome this limitation but this comes with serious challenges such as complex mathematical modelling and higher order system control. In this work, a PDC with integral part is proposed for position and input tracking control of voltage-controlled AMBS. PDC method is based on nonlinear Takagi-Sugeno (T-S) fuzzy model. …
Highly angular resolving beam separator based on total internal reflection
2019
We present an optical element for the separation of superimposed beams that only differ in angle. The beams are angularly resolved and separated by total internal reflection at an air gap between two prisms. As a showcase application, we demonstrate the separation of superimposed beams of different diffraction orders directly behind acousto-optic modulators for an operating wavelength of 800 nm. The wavelength as well as the component size can easily be adapted to meet the requirements of a wide variety of applications. The presented optical element allows one to reduce the lengths of beam paths and thus to decrease laser system size and complexity.
New approach to characterisation of electric alloys under rotating magnetic flux density
1996
The computation of electrical machines using the characterisation of electric alloys proposed by several authors gives performances not verified by experiments on actual machines. By means of finite-element-method software, the authors show that the electromagnetic context where electrical alloys are built into rotating electrical machines is completely different from the actual characterisation system. A new testing device is proposed to take into account the phenomena highlighted.
Different Permanent-Magnet Structures and their Influence on the Torque of Small DC Motors
1995
The design of permanent-magnet DC micromotors implies solving a number of problems. A few of them belong to all DC micromotors, i.e. size and number of rotor slots, width of air gap, external stator and internal rotor diameter, ratio of length to rotor diameter etc.1. One problem, certainly not the lowest in importance is, however, specific2, i.e. the choice of the most convenient permanent magnet for prescribed specifications of the micromotor. To date the progress in the production of permanent magnets has made it possible to work out different structures of motors and, for each structure, the most suitable permanent magnet for specified applications. Rare-earth permanent magnets and, in …
Evaluation of vapor mass transfer in various membrane distillation configurations: an experimental study
2011
Vapor mass transfer phenomena in four different membrane distillation (MD) configurations were examined through a self-built laboratory scale experimen- tal apparatus: Air Gap MD, Sweeping Gas MD, Vacuum Sweeping Gas MD and Vacuum MD. Vapor fluxes were measured and compared with those predicted by various models, showing that MD performance under usual processing conditions is severely controlled by the permeate side resistance to mass transfer.
Characterization of clamp-on current transformers under nonsinusoidal conditions
2009
This paper reports the performance of clamp-on current transformers under nonsinusoidal conditions. A set of experimental measurements helped to determine the ratio and the phase errors under two conditions: 1) sinusoidal excitation with frequencies from 45 to 1000 Hz and 2) nonsinusoidal excitation using the fundamental frequency and one harmonic, with adjusted phase shift. It was found that ratio and phase errors are affected by the phase angle between the harmonic and the fundamental and the harmonic amplitude. The effects of conductor location in the current transformer's window and of the air-gap width were also investigated. It was concluded that harmonic phase and ratio errors measur…
Modeling of a continuous photocatalytic reactor for isovaleraldehyde oxidation: Effect of different operating parameters and chemical degradation pat…
2013
International audience; An investigation of isovaleraldehyde (ISOV) photocatalytic oxidation was conducted at initial concentrations ranging from 25 to 150 mg/m3 and different relative humidities (5-90% RH) in order to characterize the process performances close to indoor air conditions. Experiments were carried out in two different reactors: cylinder and flat-plate photoreactor (planar reactor) at different air gap (20-60 mm) and gas residence times (0.67-5.0 s). A plug flow reactor system was developed in order to perform kinetic studies of (i) isovaleraldehyde removal, (ii) selectivity of CO2, (iii) byproducts formation and removal. It appears that ISOV removal efficiencies increased wit…
Solid rotor induction machines for use in electrically-assisted turbochargers
2006
The stator leakage reactance has a major influence on the performance of a solid rotor induction machine. It is larger and it is more difficult to define and calculate than in a cage-rotor machine. When the higher leakage reactance is taken into account, the equivalent circuit model gives predictions of sufficient precision for design purposes. The airgap, normally chosen to be quite small, is preferably quite large by general standards. The torque varies as (V/f) 3 which makes it difficult to provide a wide range of constant power operation in a variable speed application. Slitting the rotor helps to improve the characteristic for variable-speed duties.
Air gap fringing flux reduction in a high frequency inductor for a solar inverter
2013
In a gapped inductor, air gap fringing flux induces eddy currents in conductors in the vicinity of the air gap producing unwanted power loss and heat in the coil. This paper presents a detailed analysis to evaluate the performance changes of a high frequency inductor used in a solar inverter by new arrangement scheme of the air gap locations. The effect of air gap positioning in the core and the ac-resistance and leakage inductance of the high frequency inductor used in a solar inverter is investigated by using the 2-D finite element analysis. The simulation results show that a significant improvement can be achieved with limited changes in the air gap locations.